The MC54/74HC is identical in pinout to the LS .. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do. Product data sheet. Rev. 03 — 6 September 2 of Philips Semiconductors. 74HC; 74HCT Dual 4-bit binary ripple counter. 74HC datasheet, 74HC pdf, 74HC data sheet, datasheet, data sheet, pdf, Philips, Dual 4-bit binary ripple counter.
|Published (Last):||15 November 2006|
|PDF File Size:||11.88 Mb|
|ePub File Size:||13.97 Mb|
|Price:||Free* [*Free Regsitration Required]|
Product specification Supersedes data of Dec Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors aggregate and cumulative liability towards customer for the products described herein shall be limited ddatasheet accordance with the Terms and conditions of commercial sale of NXP Semiconductors.
The is specified in compliance.
The counter has an. Ordering information The is an 8-stage serial shift register. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.
They are pin compatible with Ratasheet More information. The output state is determined by eight patterns of 3-bit input. Each has two address inputs na0 and na1, an active More information.
74HC393 IC – Dual 4-bit Binary Ripple Counter IC (74393 IC)
Applications The is a edge-triggered dual JK flip-flop which features independent set-direct SDclear-direct More information. Functional diagram Fig 1. Translations A non-english translated version of a document is for reference only. It is specified in More information.
74HC393 PDF Datasheet浏览和下载
Input can be driven from either 3. Dual D-type flip-flop Rev. Non-automotive qualified products Unless this data sheet expressly states that this specific Datasheef Semiconductors product is automotive qualified, the product is not suitable for automotive use. The outputs are open-drain and can be connected to other open-drain outputs to implement active-low More information. Dual 4-input NOR gate Rev.
Ordering information The is a quad positive-edge triggered D-type flip-flop with individual data inputs Dn. This feature allows the use of these. General description The is an 8-bit synchronous down counter. The device features clock CP More information. Product data sheet 1. Applications The is a dual D-type flip-flop that features independent set-direct input SDclear-direct input.
General description The is an 8-bit D-type transparent latch with 3-state outputs. Product overview Type number.
CGD MHz, 20 db gain power doubler amplifier. Limiting values are stress ratings only and proper operation of the device at these or any other conditions above those given in the Recommended operating conditions section if present or the Characteristics sections of this document is not warranted.
Ordering information The decodes two binary weighted address inputs na0, na1 to four mutually exclusive outputs More information. Terms and conditions of commercial sale NXP Semiconductors products are sold subject to the datasjeet terms and conditions of commercial sale, as published at unless otherwise agreed in a valid written individual agreement.
This enables the use of current limiting resistors. The outputs are fully buffered for the highest noise More information. Product specification IC24 Data Handbook. Femtofarad bidirectional ESD protection diode Rev. However, if it is soldered, the solder land should remain floating or be connected to V CC. The counter has an More information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office.
Quad 2-input OR gate Rev. The substrate is attached to this pad using conductive die attach material. This device features reduced input threshold levels to allow interfacing to TTL logic More information.
74HC Datasheet PDF ( Pinout ) – Dual 4-Stage Binary Ripple Counter
General description The is a quad single pole, single throw analog switch. Each counter features a clock input ncpan overriding asynchronous master reset input nmr and 4 buffered parallel outputs nq0 to nq3. Passivated, sensitive gate triacs in a SOT54 plastic package. P tot derates linearly with 4. It has control inputs for enabling or disabling the clock CPfor clearing the counter to its More information.
The is specified in compliance More information. General description The is a high-bandwidth switch designed for the switching of high-speed UB.
Two electrically isolated dual Schottky barrier diodes series, encapsulated. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. This enables the use of current limiting resistors to interface inputs to voltages More information.
Test circuit for measuring switching times Table 9. General description The provides the non-inverting buffer. General description The is a hex inverter with Satasheet inputs.